-
product
Primary Test Equipment
LET-400
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
product
Test Block & Plug Systems
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
product
Digital Test Hammers
James Instruments? digital test hammers are an advanced, completely automated system for estimating concrete compressive strength. Its calculation, memory and recording functions allow for quick, easy and accurate test results.
-
product
N Test Finger Nail
TF-24 series
Are designed to perform tests specified in many standards to determine compliance with safety requirements.
-
product
Cellular Base Station Factory Test Systems
*Factory Test System*Designed and Built by BCO*100% Functional Testing*Environmental Stress Screening Testing
-
product
Advanced Test Platform
980 12G
The Teledyne LeCroy quantumdata 980 12G-SDI Video Generator / Analyzer module supports video and audio functional testing of next gen broadcast monitors, conversion devices and sources up to 12G-SDI. The module is equipped with four (4)12G-SDI-capable output ports. The output ports can be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. A genlock input supporting both SD analog black burst and HD tri-level to sync the output clocks with a "house sync" but the module can also run o...show more -
product
Test Board For QSFP28 Transceiver
EQSFP28
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
DSL/Gfast Test Software
Test Sentinel is a full suite of automated DSL and Gfast tools that allow a user to easily perform experiments and run standardized testing. This is the same set of tools used in our DSL and Gfast Testing Services to perform a wide variety of requests including Broadband Forum standardized tests and the Broadband Forum Gfast Certification.
-
product
IEC61850 Relay Test Set
NF802
NF802 is full digital IEC61850 relay test set, equipped with 8 optical ports, and powerful data processing capability, can realize full digital IEC61850 protection relay testing.
-
product
Battery Pack Rotate Test Device
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Pack Rotate Test Device Single storage cell safety testTest object: Battery storage pack or systemRotate the battery pack 360°around X axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Rotate the batter pack 360°around Y axis with rotation speed of 6°/s; secondly rotate it 90°,180°,270°,360°,and remain for one hour after each move. Then stop and observe for 2 hours.Accept standard: B...show more -
product
High-Voltage Test Device
PGK 70 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testin...show more -
product
Four Position Meter Test Bench
TB41
Calmet Smart Calibration Devices
The Calmet TB41 Four Position Meter Test Bench is used for calibration and simultaneously testing up to four single and three phase electromechanical and electronic acitve and reactive electricity meters with accuracy referenced to an internal reference meter (class 0.02% or 0.04%).
-
product
Built-In Relay Self-Test Diagnostic Test Tool
BIRST
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
product
10 MHz to 50/53 GHz USB Wide Dynamic Range Average Power Sensor
U2055XA
The Keysight U2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB average power sensor.
-
product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
product
System Tests Radar Pulse Stability
PN9002
Noise eXtended Technologies S.A.S.
The cost-effective PN9002 test simplifies the testing and analysis of pulse-to-pulse amplitude and phase stability for radar systems and components to 18GHz.
-
product
Multi-Device Cellular Signaling Test Solution
IQcell
Available in 2-port and 8-port configurations, IQcell™ is a cellular signaling test solution that supports the following key cellular technologies: LTE-FDD, LTE-TDD, WCDMA/HSPA, GSM. 2-Port Configuration – Turnkey Solution for IoT Device Verification. 8-Port Configuration – High Test Efficiency for Manufacturing.
-
product
Bluetooth RF Test System
FRVS
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
product
Altitude Simulation Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Altitude Simulation Test Chamber
-
-
product
Pil Dielectric Test Sets
DTS Series
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
product
Manual Test Station
We also develop manual test stations for you, which save costs for small series or are required for multi-adaptive test objects. This refers to test objects that are usually not contacted via a needle bed, but rather via plug connections.
-
product
Discharge Test System
The automated testing equipment automatically performs charge and discharge of energy devices such as the rechargeable batteries(cells, modules, packs) that are installed in PHV/ EV and mobile devices, while measuring the voltage, current, temperature, and impedance.
-
product
GENEM-C 100G Ethernet/IP Infrastructure Test Application
GENEM-C is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on the PROVA-C hardware appliance that is built on BittWare. GENEM-C allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model ca...show more -
product
Test Automation Software
INERTIA
INERTIA™ is a highly configurable automation software for real-time control, data acquisition, and test applications that enables test, manufacturing, and R&D engineers and scientists to quickly and easily develop, configure, and operate test cell systems using a configuration-based software application. INERTIA is ideal for creating, upgrading, and modernizing real-time control and data acquisition systems.
-
product
Leakage Test
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
product
Squeak And Rattle Test Solutions
Annoying noises like squeaks and rattles have become a significant quality issue for customers of passenger vehicles, light & heavy commercial vehicles, increasingly off-road vehicles, and even airplane applications. These unwanted sounds are a problem for numerous reasons including customer dissatisfaction, sizeable warranty expense, and the overlying difficulty to diagnose and fix. MB Dynamics offers an innovative line of Buzz, Squeak & Rattle (BSR) or Squeak and Rattle (S&R) Test Solutions, focused on helping to eliminate annoying noises through prevention, design verification testing, and production verification testing, before the product reaches the customer. -
product
Wireless Connectivity and IoT Test System
IQxel-M4W
Suitable for the lab or manufacturing environment, the IQxel-M4W 6G is ideal for RF testing of wireless connectivity and IoT products. The platform’s flexible software supports the most prevalent wireless connectivity standards: WLAN 802.11ax (Wi-Fi 6) and legacy (802.11a/b/g/n/ac), Bluetooth® Classic and Low Energy (Bluetooth® LE) as well as Zigbee/Thread, Z-Wave, LPWAN technologies (Sigfox, LoRa) and cellular IoT technologies (NB-IoT, LTE-M, 5G) as well as navigational technologies.
-
product
Switching System Test Tools
eBIRST
The eBIRST toolset consists of three different tools that support 200-pin LFH, 78-pin and 50-pin connectors and a set of adaptors that allow connection to other connector types. A supplied application program controls the eBIRST tools via a USB2 port that also provides the tool power and controls the switching system using a Test Definition File to define the test sequence. These tools work by measuring the path resistance at the switching system external connectors using four-wire measurements, quickly establishing whether the path is good, has increased resistance or has failed. Below are links to various eBIRST tool information:
-
product
Transformer Test Equipment
DV Power test instruments perform various diagnostic tests on power and instrument transformers. Even more, a unique feature is a condition assessment of on-load tap changers. Performing a transformer test before their breakage can be crucial.Test instruments are portable and enclosed in durable metal cases. Also, the 19” rack-mounted version suitable for factories is available as well.Applications supported by DV Power transformer test equipment include:Winding resistance measurement (IEC 60076...show more
